Black Friday Lifetime AITenders R3,990 once · Only 49 left · Ends Mon 30 Nov

Claim lifetime

Water Bath for Dielectric Testing: Supply and Installation

Open Closing: 24 Nov 2026 at 11:00 Published: 17 Nov 2026

Overview

Summary

Supply, installation, commissioning and training for a modern, temperature-controlled water bath dielectric tester used to test cable insulation at SABS. Bidders must provide a brochure, three client references, a three-year maintenance plan and ILAC-traceable calibration.

Detailed Description

The South African Bureau of Standards (SABS), through its Materials and Installation Business Unit, is seeking quotations for the delivery and installation of a new water bath dielectric tester to replace an outdated unit in its accredited cable testing laboratory. The water bath submerges cable samples to simulate wet, real-world conditions, allowing the laboratory to detect insulation defects, measure water absorption and verify that cables meet standards such as IEC 60811-402. The tender is governed by SABS RFQ 202122 and references SANS 1507-1, SANS 1507-2, SANS 1507-3, IEC 60811-402, IEC 63294 and SANS 5526.

The required system must be reliable, accurate and safe for long-term immersion testing. Key technical requirements include a stainless steel tank (AISI 304 or 316, or properly grounded metal or insulated non-conductive tank) large enough to hold cable coils without sharp bends, with a preferred size of 1,200 × 600 × 500 mm. Thermostatically controlled PID heaters (typically 230V/2000W or larger) must maintain 23 ± 2 °C and adjust up to 100 °C. The unit must include an AC or DC hipot tester capable of delivering the required voltage with leakage detection up to 40 mA, and must support immersion tests of up to 28 days for absorption and 100 days for water resistance. Safety features are mandatory: low-water-level protection, over-temperature alarms, circuit breakers (e.g., 25A) and emergency stop buttons. The unit must operate on 220V, 50Hz supply and be operated at room temperature. A calibration certificate traceable to ILAC is required.

Mandatory submission requirements are a product brochure or data sheet, at least three reference letters from previous or current clients for supplying a water bath or equivalent, and a three-year maintenance plan confirming online and physical after-sales support. The quotation must be all-inclusive of VAT and include a cost breakdown, installation, commissioning, training for up to 10 people, transport (if applicable) and disbursements (if applicable). The supplier must also provide an instruction manual and calibration certificate, and demonstrate full functionality during commissioning, with sign-off by both SABS and the supplier. Bidders must also submit a CSD registration report, a valid BBBEE certificate or sworn affidavit for specific goals, completed SBD forms and a signed Non-Disclosure Agreement. Evaluation uses the 80/20 preference point system (80 points for price, 20 for specific goals), and SABS will make no advance payment. Quotations close on 24 November 2026 at 11:00 AM and must be emailed to asanda.zulu@sabs.co.za, with no late submissions accepted. Note that Section 2 of the RFQ refers to an "automatic density meter," which appears to be a template carry-over; bidders should seek clarification on the scope through the designated procurement contact only.

Suitable Businesses

This tender is suited to manufacturers, authorised distributors and agents of electrical or laboratory test equipment, particularly dielectric, insulation and high-voltage testing systems, as well as technical service providers able to install, commission and maintain such equipment. Applicants must be CSD-registered, hold a valid BBBEE certificate or affidavit, and be able to provide three client references, a product data sheet, a three-year maintenance plan with online and on-site support, and ILAC-traceable calibration. Businesses without experience in laboratory or electrical test equipment, or without local after-sales support capability, are unlikely to meet the mandatory requirements. General suppliers and service providers outside this field should not apply.

Documents

Document 1
Added: ••• ••, ••••
Document 2
Added: ••• ••, ••••
Plans from R199/month
Plans from R199/month · AI drafting with a quoted licence

Location & Address

Street Address
••••••••••
Suburb
••••••••••
Postal Code
••••
Delivery Address
••••••••••
Plans from R199/month
Plans from R199/month · AI drafting with a quoted licence

Contact Information

Contact Person
•••• ••••
Email
••••••••@••••••••
Phone
+27 •• ••• ••••
Plans from R199/month
Plans from R199/month · AI drafting with a quoted licence

Open this tender in full

Starter gives you this tender's documents, requirements, location and buyer contacts, plus every new tender matched to your business, for R199/month.

Cancel anytime · No contract · Secure checkout by Paystack

Every tender that fits your business, for R199/month.

See your matched tenders before you pay, then get their documents and buyer contacts straight away. Cancel anytime, no contract.